WEBVTT
00:00:00.250 --> 00:00:05.260
In this video, we will be discussing what’s known as the continuity equation for fluids.
00:00:05.570 --> 00:00:13.710
The equation in question is often used to tell us how certain fluids can flow from one container to another where the volumes of the two containers are different.
00:00:14.100 --> 00:00:18.320
So to understand the continuity equation, let’s first imagine the following scenario.
00:00:18.710 --> 00:00:21.320
Let’s imagine that we’ve got a cylindrical container here.
00:00:21.450 --> 00:00:25.230
And within this cylinder, we’ve got a gas that’s flowing from left to right.
00:00:25.590 --> 00:00:27.720
Now, right now, we happen to be considering a gas.
00:00:27.720 --> 00:00:33.440
But remember, the continuity equation that we’ll be studying applies to fluids, not just gases.
00:00:33.730 --> 00:00:35.530
And remember that fluids flow.
00:00:35.580 --> 00:00:37.820
Therefore, they could be liquids or gases.
00:00:38.250 --> 00:00:41.560
But anyway, for now, we’ll just consider a gas in our cylindrical container.
00:00:42.120 --> 00:00:47.690
Now, an important assumption that we’ll make here is that the motion of all the gas molecules is mainly toward the right.
00:00:47.940 --> 00:00:50.280
The gas is flowing smoothly from left to right.
00:00:50.750 --> 00:00:57.340
In other words, we will ignore any motion of molecules that is not toward the right, since this will be minimal and not affect our fluid flow.
00:00:57.670 --> 00:01:05.060
Let’s also imagine that for every second of time that passes, one kilogram of gas moves from left to right within our container.
00:01:05.380 --> 00:01:09.950
Let’s imagine, for example, that we were to consider this position along the length of our container.
00:01:10.300 --> 00:01:13.870
We can measure the amount of gas passing this cross section per unit time.
00:01:14.140 --> 00:01:19.220
And in this case, we happen to find that one kilogram of gas is flowing per second past this cross section.
00:01:19.450 --> 00:01:27.180
This is an important quantity to remember for later because what we’ve actually found is the mass flow rate of our gas, which sounds quite complicated.
00:01:27.180 --> 00:01:32.940
But it’s just a fancy way of saying the amount of mass of gas flowing per second from left to right.
00:01:33.230 --> 00:01:42.710
And we can actually quantify the mass flow rate of our gas as the mass of the gas that’s flowing from left to right divided by the time taken for that particular amount of mass to flow.
00:01:43.160 --> 00:01:48.660
And in this particular situation, the way that we did that was to measure the amount of gas passing this point in our container.
00:01:48.830 --> 00:01:53.650
And in this particular scenario, we imagine that we found one kilogram of gas flowing per second.
00:01:54.140 --> 00:02:00.740
Now, this whole idea about mass flow rate is quite important because now let’s imagine that our container actually does this.
00:02:00.970 --> 00:02:04.970
Let’s imagine that as the gas flows from left to right, the container itself narrows.
00:02:05.300 --> 00:02:14.780
In other words, the gas is shoved into a region with a smaller cross sectional area, where specifically the cross sectional area is the area of the circle that we’ve drawn in here.
00:02:15.090 --> 00:02:18.940
As we can see, earlier on in the container, the cross sectional area was much larger.
00:02:19.190 --> 00:02:22.110
We can say that this area is 𝐴 subscript one.
00:02:22.380 --> 00:02:26.890
And now, in the smaller region of the container, we can see that the cross sectional area is different.
00:02:26.890 --> 00:02:30.110
So we will call this cross sectional area 𝐴 subscript two.
00:02:30.870 --> 00:02:32.130
Now, here’s the interesting thing.
00:02:32.270 --> 00:02:37.200
Our gas is still flowing from left to right in our container despite the fact that it suddenly narrows.
00:02:37.450 --> 00:02:40.720
So how does our gas respond to this narrowing of the container?
00:02:41.080 --> 00:02:50.590
Well, because we’re imagining a scenario where the gas molecules are simply left to their own devices traveling from left to right and we don’t exert any external forces on these gas molecules.
00:02:50.810 --> 00:02:56.870
This means that the mass flow rate in the second part of the container must be the same as the mass flow rate in the first part.
00:02:57.210 --> 00:03:02.970
The reason for this is that in the first part of the container, we’ve got a certain amount of mass flowing per second from left to right.
00:03:03.240 --> 00:03:07.470
And that mass cannot suddenly disappear at the point where the size of the container changes.
00:03:07.710 --> 00:03:12.420
That amount of mass must still flow from left to right in the narrower part of the container.
00:03:12.760 --> 00:03:23.970
Therefore, if we’ve got one kilogram of gas flowing from left to right per second in the wider part of the container, then we’ve also got one kilogram of gas flowing from left to right per second in the narrower part of the container.
00:03:24.370 --> 00:03:37.370
Now, if we give our mass flow rate a symbol, let’s say we give it the symbol 𝑅, then we can say that the mass flow rate in region one, we will call this 𝑅 subscript one, must be equal to the mass flow rate in the second region 𝑅 subscript two.
00:03:37.790 --> 00:03:47.110
At which point, we’ve arrived at a nice little consequence of the fact that a certain amount of gas flowing from left to right in the first part of the container cannot change as the shape of the container changes.
00:03:47.270 --> 00:03:56.640
And therefore, the mass flow rates in both regions must be the same because particles of gas cannot randomly appear or disappear as they move across the boundary between the first and second regions.
00:03:57.080 --> 00:04:04.620
Now, instead of considering specific value for the mass flow rate of our gas, so instead of saying one kilogram of gas flows from left to right per second.
00:04:04.850 --> 00:04:11.520
Let’s say that in the first region, a mass 𝑚 one of gas moves from left to right in a time interval 𝑡.
00:04:12.260 --> 00:04:24.280
Now, interestingly, we can imagine that at the beginning of our time interval 𝑡, if we think about gas molecules that started here, at the end of the time interval 𝑡, those gas molecules would end up further along the cylinder.
00:04:24.330 --> 00:04:26.260
In other words, they’d end up somewhere like here.
00:04:26.630 --> 00:04:32.100
And hence, we could say that over our time interval 𝑡, the molecules have moved this distance here.
00:04:32.490 --> 00:04:35.060
Let’s call this distance 𝑑 subscript one.
00:04:35.460 --> 00:04:48.540
At which point, we can think about the fact that if our gas molecules are moving this distance here, 𝑑 one over a time interval of 𝑡, then they must be moving with a speed 𝑣 one of 𝑑 one divided by 𝑡.
00:04:49.320 --> 00:04:54.690
Because, remember, the speed of an object is equal to the distance moved divided by the time taken to move that distance.
00:04:55.030 --> 00:05:03.560
Now, it’s worth noting that 𝑣 one is the speed at which the bulk of the gas moves from left to right because individual molecules may have slightly slower or slightly faster speeds as well.
00:05:03.870 --> 00:05:06.130
But, on average, they’ll be moving with a speed of 𝑣 one.
00:05:06.480 --> 00:05:16.400
And another interesting thing to note is that the gas which initially started out here at the beginning of our time interval and finished up here has actually occupied this amount of volume.
00:05:16.920 --> 00:05:26.270
This is a cylindrical volume naturally because our container is a cylinder with a cross sectional area of 𝐴 one, same as this cross sectional area here, and a length of 𝑑 one.
00:05:26.950 --> 00:05:37.010
At which point, we can recall that the volume of a cylinder given by what we will call capital 𝑉 is equal to 𝐴, the cross sectional area of the cylinder, multiplied by 𝑑, the length of the cylinder.
00:05:37.280 --> 00:05:49.280
And hence, we can say that the volume occupied by the gas that we happen to be considering, specifically the gas with mass 𝑚 one moving from left to right a distance 𝑑 one over a time interval 𝑡, is given by capital 𝑉 subscript one.
00:05:49.580 --> 00:05:56.610
Is equal to 𝐴 one, that’s the cross sectional area of the cylinder, multiplied by 𝑑 one, that’s the distance the gas travels from left to right.
00:05:56.950 --> 00:06:06.040
And by the way, we need to be careful in differentiating between lowercase 𝑣, which is the speed of the gas as it moves from left to right, and uppercase 𝑉, which is the volume that the gas occupies.
00:06:06.440 --> 00:06:10.400
Now, at this point, we might be wondering, what’s the point of writing down all of these equations?
00:06:10.720 --> 00:06:14.960
Well, remember that we’re trying to link back our gas’s behavior to its mass flow rate.
00:06:15.240 --> 00:06:19.470
And we’re considering the mass of gas that moves from left to right over a time interval 𝑡.
00:06:19.960 --> 00:06:30.620
We know that the particular amount of gas that we’re considering has a mass of 𝑚 one and occupies a volume of 𝑉 one, which means that at this point, we can recall a quantity known as density, signified by the letter 𝜌.
00:06:31.040 --> 00:06:36.030
The density of an object is equal to its mass divided by the volume that it occupies.
00:06:36.320 --> 00:06:43.460
And so we can quantify the mass of our gas, in this case, 𝑚 one, in terms of the density of the gas and the volume that it occupies.
00:06:43.540 --> 00:06:49.100
Because we can also say that in the first region of the cylinder, the gas has a density 𝜌 subscript one.
00:06:49.480 --> 00:07:01.650
So taking this equation and rearranging it by multiplying both sides of the equation by the volume 𝑉, we find that the mass of the gas, 𝑚 one, is equal to the density of the gas, 𝜌 one, multiplied by the volume it occupies, 𝑉 one.
00:07:02.050 --> 00:07:09.100
So we’re getting closer to quantifying our mass flow rate in the first region of the container in terms of certain properties of the gas and the container.
00:07:09.100 --> 00:07:13.250
Specifically the density of the gas and the volume of the container occupied by that gas.
00:07:13.410 --> 00:07:18.430
Which we will now express in terms of the cross sectional area of the cylinder and the distance that the gas moves.
00:07:18.810 --> 00:07:22.400
In other words, we can say that the volume 𝑉 one is equal to 𝐴 one 𝑑 one.
00:07:22.690 --> 00:07:38.480
And now, finally, we can substitute into our mass flow rate equation that the mass flow rate on the left-hand side of the cylinder, which is 𝑅 one, and we know this to be equal to 𝑚 one divided by 𝑡, is actually equal to 𝜌 one 𝐴 one 𝑑 one divided by 𝑡.
00:07:38.750 --> 00:07:48.700
So we’ve expressed the mass flow rate in the first part of the container in terms of the density of the gas, the cross sectional area of the cylinder, and the distance that the gas moves in a time interval 𝑡.
00:07:49.140 --> 00:07:53.650
But then, at this point, we can also look at this part of our fraction here, 𝑑 one divided by 𝑡.
00:07:53.850 --> 00:08:00.320
And recall that 𝑑 one divided by 𝑡 is actually equal to lowercase 𝑣 one, the speed at which the gas moves from left to right.
00:08:00.680 --> 00:08:11.390
And so we find that the mass flow rate in the first part of the container is equal to the density of the gas multiplied by the cross sectional area of the cylinder multiplied by the speed at which the gas is moving from left to right.
00:08:11.840 --> 00:08:14.530
All of which are known quantities on the right-hand side now.
00:08:14.870 --> 00:08:16.310
And here’s where things get interesting.
00:08:16.620 --> 00:08:24.670
Remember we arrived at a conclusion early on that the mass flow rate in the second part of our container must be the same as the mass flow rate in the first part of the container.
00:08:25.130 --> 00:08:32.630
Therefore, if we also say that the mass flow rate in the second part of the container, 𝑅 two, is equal to the density of the gas in the second part of the container.
00:08:32.710 --> 00:08:40.100
Multiplied by the cross sectional area of the second part of the container multiplied by the speed with which the gas moves from left to right in the second part of the container.
00:08:40.450 --> 00:08:45.910
And then we use the equation 𝑅 one is equal to 𝑅 two and substitute in the right-hand sides of both equations.
00:08:46.200 --> 00:08:48.510
Then we arrive at this equation here.
00:08:48.710 --> 00:08:51.460
This is known as the continuity equation for fluids.
00:08:51.750 --> 00:08:56.710
This is a very useful and important equation when it comes to the analysis of a smoothly flowing fluid.
00:08:57.040 --> 00:09:00.670
And although we don’t need to know off by heart how we derive this equation.
00:09:00.970 --> 00:09:06.070
It’s important to have seen how it’s derived so that we understand the deeper meaning behind these symbols.
00:09:06.330 --> 00:09:12.400
Now, interestingly, this equation applies fairly generally, and it can tell us how our fluid must behave as it flows.
00:09:12.680 --> 00:09:20.970
In this particular diagram, we’re considering a gas flowing from left to right through a container that has a smaller cross sectional area in the second region compared to the first.
00:09:21.370 --> 00:09:30.310
So one thing that we can say is that the cross sectional area of the first region of the container, 𝐴 one, is larger than the cross sectional area of the second region, 𝐴 two.
00:09:30.800 --> 00:09:37.450
But then, if 𝜌 one 𝐴 one 𝑣 one has to be equal to 𝜌 two 𝐴 two 𝑣 two and 𝐴 one is bigger than 𝐴 two.
00:09:37.670 --> 00:09:48.340
Then this must be compensated for by an increase in the value of 𝜌 two, the density of the gas, or an increase in value of 𝑣 two, the speed at which the gas moves, or both.
00:09:48.670 --> 00:09:56.760
In other words, either we find that 𝜌 one is less than 𝜌 two or 𝑣 one is less than 𝑣 two or some element of both of these above conditions.
00:09:57.080 --> 00:09:59.590
And if we think about it, this makes intuitive sense as well.
00:09:59.800 --> 00:10:01.780
We’ve got a larger container on the left-hand side.
00:10:01.780 --> 00:10:05.180
And a gas is moving at a certain speed from left to right through this container.
00:10:05.460 --> 00:10:13.780
And as it enters a narrower container, either the gas must flow faster so that the same amount of mass is transferred from left to right in the same amount of time.
00:10:14.010 --> 00:10:20.420
Or all the particles must be squished in to a smaller volume, so the density increases, or some element of both.
00:10:20.700 --> 00:10:26.120
Now, in this particular situation because we’re considering a gas, it’s likely that some element of both will happen.
00:10:26.330 --> 00:10:31.030
In the narrower part of the container, the density and the speed with which the gas moves will increase.
00:10:31.450 --> 00:10:37.430
However, there is one particular type of material that behaves in a way that would only result in one of these changes occurring.
00:10:37.840 --> 00:10:40.810
One example of such a material is, in fact, water.
00:10:41.360 --> 00:10:44.460
Water is what’s known as an incompressible fluid.
00:10:44.810 --> 00:10:47.900
And essentially, what this means is that it cannot be compressed.
00:10:48.170 --> 00:10:57.470
If we look on a molecular level so that we’re looking at individual water molecules here, then, as it turns out, water molecules cannot be forced together into a smaller volume.
00:10:57.660 --> 00:11:01.980
In other words, let’s say we’ve got 100 molecules of water here, and they occupy a specific volume.
00:11:02.230 --> 00:11:07.610
We cannot exert a force on this volume here to make these water molecules occupy a smaller volume.
00:11:07.850 --> 00:11:10.220
We cannot shove these water molecules closer together.
00:11:10.350 --> 00:11:12.610
That’s why water is incompressible.
00:11:12.840 --> 00:11:17.780
And a consequence of this is that a certain number of molecules will always occupy a certain volume.
00:11:18.040 --> 00:11:21.630
And that volume cannot be compressed so that those molecules occupy a smaller volume.
00:11:21.780 --> 00:11:32.850
And because that certain number of molecules has a certain mass, essentially, what we’re saying is that for a particular mass of water molecules, the volume occupied by that mass must be constant.
00:11:34.940 --> 00:11:40.970
Or, in other words, the mass per unit volume is constant for water, and therefore the density of water is constant.
00:11:41.390 --> 00:11:49.150
What this means is that as water flows from left to right, from the wider part of the cylinder to the narrower part of the cylinder, the density cannot change.
00:11:49.680 --> 00:11:59.310
So what we’ve got in this particular scenario, as we move from left to right, is that the cross sectional area of the first part of the cylinder is greater than the cross sectional area of the second part of the cylinder.
00:11:59.620 --> 00:12:04.920
But because we’ve got water flowing through this container, the density on both sides of the container must be the same.
00:12:04.960 --> 00:12:06.340
It’s an incompressible fluid.
00:12:06.720 --> 00:12:17.780
And hence, the only way to ensure that 𝜌 one 𝐴 one 𝑣 one is equal to 𝜌 two 𝐴 two 𝑣 two is to result in a corresponding increase in 𝑣 two, the speed with which the water moves in this part of the container.
00:12:18.220 --> 00:12:22.960
Since the water cannot be compressed, the same mass of water must occupy the same volume.
00:12:23.260 --> 00:12:25.620
But the cross sectional area is decreasing.
00:12:25.860 --> 00:12:29.350
So the length along the cylinder occupied by the water must increase.
00:12:29.650 --> 00:12:31.800
The water must flow faster to the right.
00:12:32.200 --> 00:12:40.620
In other words, what we find is that 𝑣 one, the speed with which the water moved in the first part of the container, is less than 𝑣 two, the speed with which it moves in the second part of the container.
00:12:41.080 --> 00:12:46.500
And so that is what happens when we apply the continuity equation to an incompressible fluid, such as water.
00:12:46.840 --> 00:12:52.630
At which point, we’ve seen the derivation of the continuity equation and seen how it can be applied to a couple of different fluids.
00:12:53.050 --> 00:12:55.810
So let’s now summarize what we’ve talked about in this lesson.
00:12:56.260 --> 00:13:04.230
Firstly, we saw that the continuity equation relates the mass flow rates of a smoothly flowing fluid at different points along its flow path.
00:13:04.490 --> 00:13:29.660
Specifically, we saw that for a fluid flow being compared at two different positions along its flow, positions one and two, the continuity equation tells us that the density of the fluid multiplied by the cross sectional area of the container it’s flowing through multiplied by the speed at which the fluid flows in position one must be equal to the density of the fluid multiplied by the cross sectional area multiplied by the speed at which the fluid flows in position two.
00:13:30.070 --> 00:13:35.150
And we saw it used in a context where positions one and two were actually regions one and two.
00:13:35.300 --> 00:13:40.050
And region two featured a change in the cross sectional area of the container compared to region one.
00:13:40.300 --> 00:13:49.700
Which brings us on to our final point, which is that the equation is commonly used to describe the effects of a change in the cross sectional area of the container that the fluid is flowing through.
00:13:50.200 --> 00:13:52.920
But the equation is not limited to this purpose.
00:13:53.220 --> 00:13:59.970
The continuity equation can be used to describe changes in the properties of a fluid flow when any of these quantities change.
00:14:00.360 --> 00:14:03.920
And that is an overview of the continuity equation for fluids.